Series 30 Rectifier
The Series 30 is a primary SCR, single transformer, DC power supply for low voltage plating/anodizing applications. It is available in air- or water-cooled configurations; plus NEMA 1, NEMA 2, NEMA 3R, or NEMA 4X enclosure ratings.
Input voltages ranging from 208V – 600VAC, three phase 60Hz or 50Hz
Input AC Voltage: 208V – 600V
Output DC Voltage Range: 6V – 100V
Output DC Current Range: 500A – 10,000A
- Highly efficient all-copper transformer construction
- Standard remote control panel
- Air- or water-cooled flexibility
- Domestic and international voltage capability
- Low ripple
- Tight voltage and current regulation
- Diagnostic options for ease of maintenance
- Input Line Variation: +/- 5% from nominal (± 10% optional)
- Output Voltage Regulation: ± 0.5%
- Output Current Regulation: ± 0.5%
- AC RMS Output Ripple at Full Voltage and Current: 5% RMS
- Optional AC RMS Output Ripple at Full Current: 1% or 5% @ 25% to 100% output voltage
- Efficiency 85% – 90%
Learn more about this product! Read our brochures and other supporting documents!
How can I reduce or eliminate downtime?
- Purchasing and installing a second backup rectifier connected in parallel with the existing rectifier and a DC switch, will virtually eliminate downtime. In this scenario, if a rectifier happens to go down or is being serviced, a backup unit can be brought online within a few minutes. For more information, see our Options document entitled "DC Transfer Switches" for details about DC switch and backup rectifier configurations.
What size rectifier do I need?
- Rectifier sizing has many variables including part size, anode cell surface area, chemical characteristics, and process time. The chemical or the system supplier usually recommends the rectifier size required for the process.
Which is better: air- or water-cooling?
- The environment where the rectifier will be placed usually determines the best type of cooling. For harsh, corrosive, or high-temperature environments, water-cooling is best suited.
What is the advantage of a primary SCR, single transformer design?
- The low voltage, single transformer design (Series 30) uses primary SCRs for regulation. The SCRs supply AC power to the primary of the transformer. The transformer has a star secondary with a diode connected to each leg for rectification. This design has a low overall component, which makes it very reliable and price competitive.
Do I need a ripple filter?
- Ripple is the small AC voltage or current occurring in a DC component as an unavoidable byproduct of rectification. Ripple filtering is a combination of inductance and capacitance used to reduce the level of ripple. Ripple filtering is required on most chrome processes where a decorative or good finish is required. Filtering is also required for loads that are sensitive to AC RMS ripple.
Which leg of the rectifier is grounded?
- The rectifier output is isolated, allowing either leg to be grounded per process requirements.
Can I control or monitor the rectifier with my PLC?
- Yes. As an option, Controlled Power Company offers single channel computer interface cards for monitoring and/or control of the rectifier. The computer interface card can be configured for 0 to 10 volt, 0 to 5 volt, or 4 to 20 mA signals. Additionally, we offer integrated distributed I/O modules so that communications with the PLC can be performed over Ethernet or serial connections, instead of running analog signals.
How can I reduce the floor space needed for rectifiers used in my process?
- Controlled Power Company is able to custom-design rectifier cabinets for limited floor space or single-side access. We are also able to provide multiple rectifiers in a single enclosure.
Do I need a separate feeder transformer for the rectifier?
- The rectifier does not require a separate feeder transformer; however depending on site requirements, one may be necessary. Please discuss this with an electrical contractor or a consultant for further information.
When do I need a DC switch?
- A DC switch is used for isolating the output of a rectifier and may be configured for various applications to reduce downtime. When downtime is unacceptable, a DC switch connected to the normal production unit and a standby unit provides a quick means of switching between the two in the event of a failure or for routine maintenance. The DC switch ensures that DC power is not present in the rectifier, so that it can be serviced safely by repair personnel. While the down unit is being serviced, the other unit will operate normally. You will not need to shut down the line when servicing the rectifiers. A DC switch may also be configured to switch one rectifier between multiple tanks.
How can I increase my rectifier current output?
- A second Series 30 rectifier may be connected in parallel. The parallel control option will allow both units to equally share the load current. Some changes to the existing unit may be required.
Controlled Power Company warrants the Series 30 Rectifier to be free from defects in material and workmanship for a period of two (2) years following shipment from the factory. Controlled Power Company agrees to replace, F.O.B. its factory, any parts which fault through defect in material or workmanship during the warranty period.
Consult the factory for additional warranty details, and a description of start-up services provided.
Sign Up for news
SEE WHAT’S NEW ON OUR NEWS + BLOGVIEW ALL POSTS
CPC’s “Egress Lighting Integrity Test”
In terms of monitoring, testing, data recording, and recordkeeping, the matrix below shows which of our centralized emergency lighting inverters meet or exceed NFPA 101 (up through and including section 22.214.171.124.3). Compliance With NFPA…read more >
Solutions To Electrical Power Disturbances
Have you ever wanted a simple matrix that illustrates “which types of electrical power quality products solve which types of power problems”? We have just such a document to help you! Our “Solutions To Electrical…read more >
Controlled Power Company Launches Newly Re-Designed Website
Controlled Power Company, a U.S. manufacturer of a full line of commercial, industrial, and medical-grade electrical power quality solutions, announces the launch of its newly re-designed website, www.controlledpwr.com. Using a contemporary development platform, the new…read more >
Emergency Egress Lighting Solutions
Just curious … as a lighting designer or specifying engineer, are you able to thoroughly investigate the available commercial / industrial emergency egress lighting solutions? As you specify UL 924 Listed battery backup products (for example, wall-mounted “bug-eyes”, emergency ballasts,…read more >